Stud Welding Products, Inc. - FREE Quotes on Welding Studs, Welding Supplies, Welding Equipment for Stud Welding

Headed Anchor Studs

STUD SPECIFICATIONS
D	A	H
1/4	.187	.500
3/8	.281	.750
1/2	.281	1.000
5/8	.312	1.250

Description	Pounds M Pieces	Part Number
1/4 X 1 1/8	18	HA0250112
1/4 X 2 11/16	43	HA0250268
1/4 X 4 1/8	65	HA0250412
3/8 X 1 3/8	69	HA0370137
3/8 X 1 5/8	75	HA0370162
3/8 X 2 1/8	93	HA0370212
3/8 X 2 5/8	108	HA0370262
3/8 X 3 1/8	126	HA0370312
3/8 X 3 5/8	145	HA0370362
3/8 X 4 1/8	155	HA0370412
3/8 X 6 1/8	218	HA0370612

All S.W.A headed anchors meet AWS specifications. Test reports available upon request.

HEADED ANCHOR STUDS are designed to be welded to flat surfaces or welding in the fillet or to the heel of angles. When ordering, specify if studs are to be welded to flat surfaces or in fillet or to heel of angle. All orders for studs include required ferrules.

LENGTH: Length is before weld. Stud diameters (D) 1/2" and below will be approximately 1/8" shorter after welding. 5/8" will be approximately 3/16" shorter after welding.

MATERIAL: Low carbon steel ASTM A108

STAINLESS STEELS: HA studs are also available in stainless steel

FERRULE SPECIFICATIONS
No.	D	B	F	M
FF-025	.454	.380	.234	.390
FF-037	.640	.505	.234	.390
FF-050	.795	.650	.250	.438
FF-062	1.030	.785	.328	.516

Description	Pounds M Pieces	Part Number
1/2 X 1 5/8	130	HA0500162
1/2 X 2 1/8	170	HA0500212
1/2 X 2 5/8	197	HA0500262
1/2 X 3 1/8	226	HA0500312
1/2 X 4 1/8	292	HA0500412
1/2 X 5 5/16	341	HA0500531
1/2 X 6 1/8	393	HA0500612
1/2 X 8 1/8	504	HA0500812
1/2 X 10 1/8	630	HA0501012
5/8 X 2 11/16	315	HA0620268
5/8 X 3 3/16	360	HA0620318
5/8 X 4 3/16	450	HA0620418
5/8 X 5 3/16	560	HA0620518
5/8 X 6 9/16	652	HA0620656
5/8 X 8 3/16	793	HA0620818
5/8 X 10 3/16	1039	HA0621018

Mechanical Property Requirements

Type A¹

Type B²

Tensile Strength

55,000 psi min
(380 MPa)

60,000 psi min
(415 MPa)

Yield Strength
(0.2% offset)

50,000 psi min
(345 MPa)

Elongation
(% in 2-in.)

17% min

20% min

Reduction of Area

50% min

¹	Type A studs shall be general purpose of any type and size used for purposes other than shear transfer in composite beam design and construction.

²	Type B studs shall be studs that are heated, bent, or of other configuration in 1/2 in (12.7 mm), 5/8 in (15.9 mm), 3/4 in (19 mm), 7/8 in (22.2 mm), and 1 in (25.4 mm) diameter that are used as an essential component in composite beam design and construction.